Saati SAATITEX PHU BLUE Pure Photopolymer Emulsion
APPLICATIONS
Garment printing.
GENERAL CHARACTERISTICS
- Red pure photopolymer direct emulsion resistant to plastisol, water based and discharge inks without catalyst
- Outstanding abrasion and humidity resistance
- Excellent print definition on any mesh
- 45% solids content
- Exposes two times faster than a diazo or dual-cure emulsion
- Suitable for DLE (diodes) exposure
DIRECTIONS FOR USE
Handle under yellow safelight or low wattage tungsten lights. Avoid exposure to daylight, quartz/halogen lamps, cool white fluorescent lamps or discharge lamps.
Sensitizing and mixing
Emulsion is pre-sensitized during production and does not require mixing.
Mesh preparation and degreasing
Degrease and abrade new mesh with Direct Prep 1 (abrasive gel) in order to optimize stencil adhesion; dry and store the screen in a dust free, dry environment prior to coating. For further applications, thoroughly degrease the mesh prior to use with Direct Prep 2 (degreaser).
Coating
Using a high quality scoop coater or coating through, apply one or two coats to the substrate side of the screen, followed by one or two coats on the squeegee side. For a thicker stencil, apply additional coats to the squeegee side prior to drying. For a higher quality stencil with a minimal increase in stencil thickness, apply one or two additional coats to the substrate side of the screen after the initial coats have dried.
Drying and storage
Thoroughly dry the coated screen at a maximum temperature of 104°F (40?C) in a dust free, dark or yellow light area, with the substrate side facing down to optimize stencil quality.
Coated screens should be stored in a dust free, dry, safelight environment.
Exposing
Ensure that all surfaces (emulsion, film and glass) are free of dust to minimize pinholes.
Contact the emulsion side of the positive with the substrate side of the screen and secure in position before placing the screen in a suitable vacuum frame. Many variables, such as lamp type and age, distance from lamp to screen, mesh type and coating thickness, can affect exposure time. Perform an exposure test with one of two calculators now available (Exposure Calculator and 21 Step Sensitivity Guide) to determinate correct exposure time for a complete cure.
Developing
Wet both sides of the screen with a strong, finely divided spray of water and continue washing out until all image areas are fully open. Rinse both sides of the screen and dry thoroughly before use. A properly exposed and developed screen will not leave residues on the squeegee side.
Post exposing
Post expose with daylight or exposure UV lamp to produce a more water-resistance stencil.
Reclaiming
Remove all ink residues immediately after printing with an appropriate solvent. Remove stencil with Remove ER1, ER2, ER4, ER5, ER6, ER10 or ER25 and a pressure washer. For stains and ghost images, use Remove HR3 followed by a pressure washer.
HEALTH AND SAFETY
Before using, refer to appropriate material safety data sheets.
PROBLEM SOLVING
Poor coating quality
- Properly clean, degrease and rinse the screen to remove all residues and traces of chemicals
- Properly and evenly tension the fabric
- Clean and ensure the scoop coater does not present any defect edge.
Poor detail or difficulty washing out image
- Ensure emulsion and coated screens are handled in safelight conditions only
- Ensure a minimum vacuum of 0.66 bar (500 mmHg or 20 in Hg) on vacuum gauge for optimum contact of the positive
- Optimize exposure time and use only high quality film positives
- Do not store emulsion or coated screen at high temperatures.
Emulsion falls off, extreme pinholes or severe stencil breakdown during printing
- Ensure that damp screens are not being exposed
- Only expose screens with an even and consistent coating thickness
- Ensure that stencil has not been severely underexposed
- Ensure emulsion is not too old and has not been stored at high temperature.
Difficulty reclaiming screens
- Non reclaimable once catalysed
- Optimize exposure time and properly rinse the squeegee side of the screen during developing to remove all residual traces, especially when using higher mesh count dyed fabric.
STORAGE
When sealed in the original container and stored in cool conditions, SAATITEX PHU-2 will maintain original properties for 24 months from the date of production.
